|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
1/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f chip tantalum capacitors tc series a case ? features (a) ? dimensions (unit : mm) 1) vital for all hybrid integrated circuits board application. 2) wide capacitance range. 3) screening by thermal shock. ? part no. explanation m 0 j 8 r t 1 0 6 c a rated voltage capacitance tolerance nominal capacitance in pf in 3 digits: 2 significant figures followed by the figure representing the number of 0's. 8 : reel width : 8mm r : positive electrode on the side opposite to sprocket ho le 1 6 1 3 6 4 2 5 1 1 series name tc 2 case style 3 4 nominal capacitance 5 taping 20% m : + ? 4 code 6.3 0j 10 1a 16 1c 20 35 1d 1v 25 1e rated voltage ( v) 0g tc a dimensions l h s w 2 w 1 s s w h l w anode mark 2 1 (unit : mm) 3.2 0.2 + ? 1.6 0.2 + ? 1.2 0.2 + ? 1.6 0.2 + ? 0.8 0.3 + ? a case + ?
2/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f data sheet tc series a case ? rated table ( f) rated voltage (v) 4 0g 1 (105) a 1.5 (155) a 2.2 (225) a 3.3 (335) a a a a a a a a a 4.7 (475) a 6.8 (685) a a a a a 10 (106) a a a a a a a a a aa a a 15 (156) a 22 (226) a a a a 33 (336) 47 (476) 68 (686) 100 (107) 150 (157) a a a a 6.3 0j 10 1a 16 1c 20 1d 25 1e remark) case size codes (a) in the above show products line-up. ? under development a a a 35 1v ? ? ? ? ? marking j a j a the indications listed below should be given on the surface of a capacitor. (1) polarity : the polarity should be shown by bar. (on the anode side) (2) rated dc voltage : due to the small size of a case, a voltage code is used as shown belo w. (3) visual typical example (1) voltage code (2) capacitance code voltage code rated dc voltage (v) g j a c d v 4 6.3 10 16 20 35 e25 capacitance code nominal capacitance ( f) a e j n s w a e j n 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 s47 w68 100 [ a case] note 1) note 2) voltage code and capacitance code are variable with parts number ? (1) j ? (2) a a ? 3/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f data sheet tc series a case ? characteristics item performance test conditions (based on jis c 5101 ? 1 and jis c 5101 ? 3) operating temperature ? 55 c~ + 125 c maximum operating temperature with no voltage derating + 85 c rated voltage (vdc) 20 25 16 10 6.3 4 category voltage (vdc) 13 16 10 6.3 4 2.5 surge voltage (vdc) 13 8 526 20 32 dc leakage current 0.5 a or 0.01cv whichever is greater shown in " standard list " capacitance tolerance measuring frequency : 100 10khz measuring voltage : 0.5vrms or less measuring circuit : dc equivalent series circuit tangent of loss angle (df, tan ) impedance resistance to soldering heat temperature cycle moisture resistance there should be no significant abnormality. the indications should be clear. appearance c / c df (tan ) l.c. shall be satisfied the voltage on " standard list " measuring frequency : 120 12hz measuring voltage : 0.5vrms + 1.5 to 2v.dc measuring circuit : dc equivalent series circuit shall be satisfied the voltage on " standard list " at 85 c at 125 c at 85 c voltage : rated voltage for 1min shall be satisfied allowance range. 20% measuring frequency : 120 12hz measuring voltage : 0.5vrms + 1.5 to 2v.dc measuring circuit : dc equivalent series circuit less than initial limit voltage reduction when temperature exceeds + 85 c 35 22 44 as per 4.9 jis c 5101-1 as per 4.5.1 jis c 5101-3 as per 4.7 jis c 5101-1 as per 4.5.2 jis c 5101-3 as per 4.8 jis c 5101-1 as per 4.5.3 jis c 5101-3 as per 4.10 jis c 5101-1 as per 4.5.4 jis c 5101-3 as per 4.14 jis c 5101-1 as per 4.6 jis c 5101-3 dip in the solder bath solder temp : 260 10 c duration : 5 0.5s repetition : 1 after the specimens, leave it at room temperature for over 24h and then measure the sample. as per 4.16 jis c 5101-1 as per 4.10 jis c 5101-3 as per 4.22 jis c 5101-1 as per 4.12 jis c 5101-3 others : within 5% of initial value there should be no significant abnormality. the indications should be clear. appearance c / c df (tan ) l.c. less than initial limit after leaving the sample under such atmospheric condition that the temperature and humidity are 60 2 c and 90 to 95% rh,respectiveiy, for 500 12h leave it at room temperature for over 24h and then measure the sample. tca0g686m8r : within 15% of initial value tca0g107m8r : within 20% of initial value others : within 10% of initial value others : within 10% of initial value others : less than initial limit there should be no significant abnormality. the indications should be clear. appearance c / c df (tan ) l.c. less than initial limit repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. less than initial limit tca0g686m8r : within 15% of initial value temp. time 1 2 3 4 room temp. room temp. 3min.or less 3min.or less 30 3min. 30 3min. ? 55 3 c + ? 125 2 c + ? tca0g686m8r : within 15% of initial value tca0g107m8r : within 20% of initial value tca0g107m8r : within 20% of initial value tca0j476m8r : within 15% of initial value tca0g686m8r : less than 150% of initial limit tca0g107m8r : less than 150% of initial limit after the specimens, leave it at room temperature for over 24h and then measure the sample. tca1a226m8r : within 15% of initial value tcap0j226 : less than 150% of initial limit others : less than initial limit 4/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f data sheet tc series a case item performance test conditions (based on jis c 5101 ? 1 and jis c 5101 ? 3) temperature stability surge voltage shall be satisfied the voltage on " standard list " as per 4.29 jis c 5101-1 as per 4.13 jis c 5101-3 as per 4.23 jis c 5101-1 as per 4.15 jis c 5101-3 as per 4.35 jis c 5101-1 as per 4.9 jis c 5101-3 temp. appearance there should be no significant abnormality. temp. ? 55 c + 85 c df (tan ) l.c. l.c. less than 1000% of initial limit shall be satisfied the voltage on " standard list " df (tan ) shall be satisfied the voltage on " standard list " df (tan ) l.c. less than 1250% of initial limit temp. + 125 c c / c within 0/ ? 12% of initial value c / c within + 15/0% of initial value c / c others : within + 10/0% of initial value ? loading at high temperature c / c df (tan ) l.c. l.c. shall be satisfied the voltage on " standard list " less than initial limit after applying the rated voltage for 2000 + 72/0 h without discontinuation via the serial resistance of 3 or less at a temperature of 85 2 c , leave the sample at room temperature / humidity for over 24h and measure the value. as per 4.26jis c 5101-1 as per 4.14jis c 5101-3 apply the specified surge voltage via the serial resistance of 1k every 5 0.5 min. for 30 5 s. each time in the atmospheric condition of 85 2 c. repeat this procedure 1,000 times. after the specimens, leave it at room temperature for over 24h and then measure the sample. df (tan ) less than initial limit others : 10% of initial value c / c tca0g686m8r : within 15% of initial value tca0g107m8r : within 20% of initial value tca0j476m8r : within 15% of initial value there should be no significant abnormality. appearance there should be no significant abnormality. appearance terminal strength the measured value should be stable. a force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (see the figure below) capacitance 1 f (apply force) (unit : mm) 20 50 r230 45 45 thickness=1.6mm tca0g686m8r : within + 12/0% of initial value tca0g107m8r : within + 12/0% of initial value tca0g686m8r : within 15% of initial value tca0g686m8r : less than 125% of initial limit tca0g107m8r : less than 125% of initial limit tca1a226m8r : less than 125% of initial limit tca1e105m8r : less than 125% of initial limit tca1a226m8r : within 15% of initial value tca0g107m8r : within 20% of initial value others : within 10% of initial value others : less than initial limit 5/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f data sheet tc series a case item performance test conditions (jis c 5101 ? 1 and jis c 5101 ? 3) adhesiveness dimensions the terminal should not come off. as per 4.34 jis c 5101-1 as per 4.8 jis c 5101-3 apply force of 5n in the two directions shown in the figure below for 10 1s after mounting the terminal on a circuit board. apply force a circuit board product ja refer to "external dimensions" measure using a caliper of jis b 7507 class 2 or higher grade. resistance to solvents the indication should be clear as per 4.32 jis c 5101-1 as per 4.18 jis c 5101-3 dip in the isopropyl alcohol for 30 5s, at room temperature. solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. as per 4.15.2 jis c 5101-1 as per 4.7 jis c 5101-3 dip speed=25 2.5mm / s pre ? treatment(accelerated aging): leave the sample on the boiling distilled water for 1 h. solder temp. : 245 5 c duration : 3 0.5s solder : m705 flux : rosin 25% ipa 75% capacitance vibration appearance measure value should not fluctuate during the measurement. there should be no significant abnormality. as per 4.17 jis c 5101-1 frequency : 10 to 55 to 10hz/min. amplitude : 1.5mm time : 2h each in x and y directions mounting : the terminal is soldered on a print circuit board . 6/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f data sheet tc series a case ? standard products list, tc series a case 22 0.9 33 1.3 47 68 1.9 2.7 0.5 3.3 1.5 4 10 0.5 0.5 0.5 15 0.6 tc a 0g 475m8r tc a 0g 106m8r tc a 0g 156m8r tc a 0g 226m8r tc a 0g 336m8r tc a 0g 476m8r tc a 0g 686m8r tc a 0j 335m8r 4.7 tc a 0g 685m8r 6.8 tc a 0j 475m8r 4.7 2.2 tc a 0j 685m8r tc a 0j 106m8r 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 16 10 20 16 10 20 16 10 20 6.8 3.3 10 4.7 0.5 15 tc a 0j 156m8r tc a 0j 226m8r 22 3.0 0.7 tc a 0j 336m8r tc a 0j 476m8r tc a 1a 155m8r tc a 1a 225m8r tc a 1a 335m8r tc a 1a 475m8r tc a 1a 685m8r 33 2.1 0.9 47 6.8 10 6 10 12 18 6 10 12 18 14 30 34 10 14 30 34 8 8 12 10 8 12 10 8 12 10 8 12 10 12 16 24 8 8 12 10 0.5 8 12 10 8 12 10 8 12 10 12 16 24 0.5 6 10 8 0.5 6 10 8 0.5 8 12 10 0.5 4 3 3.5 3.2 3 5.6 4.9 5.6 4.9 4.2 3.5 3.2 3.2 8.8 5.6 4.9 8 12 10 4.2 8 12 10 4 8 12 10 3 10 14 12 3.5 12 30 16 3.2 4.2 4 3 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 100 4 tc a 0g 107m8r 4 2.5 5 30 54 36 3 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 1.0 tc a 1a 106m8r 10 1.5 tc a 1a 156m8r 15 2.2 6 10 8 7 0.5 6 10 8 5.6 0.5 20 + ? 20 + ? 20 + ? 20 + ? 20 + ? 6 10 8 4.9 0.5 6 10 8 4.8 6 10 8 3.9 6 10 8 3.8 8 12 10 3.5 0.5 tc a 1a 226m8r 22 tc a 1c 105m8r 1 tc a 1c 155m8r 1.5 tc a 1c 225m8r 2.2 tc a 1c 335m8r 3.3 10 20 16 10 20 16 10 20 16 10 20 16 0.8 tc a 1c 475m8r 4.7 1.1 tc a 1c 685m8r 6.8 1.6 tc a 1c 106m8r 10 0.6 1.4 20 + ? 6 10 8 7 16 32 25 0.5 tc a 1e 105m8r 1 20 + ? 6 10 8 6 13 26 20 0.5 tc a 1d 155m8r 1.5 20 + ? 6 10 8 5.2 16 32 25 0.6 tc a 1e 225m8r 2.2 20 + ? 6 10 8 5.2 13 26 20 0.5 tc a 1d 225m8r 2.2 20 + ? 6 10 8 4.8 13 26 20 0.7 tc a 1d 335m8r 3.3 20 + ? 6 10 8 3.9 13 26 20 0.9 tc a 1d 475m8r 4.7 20 + ? 6 10 8 7 13 26 20 0.5 tc a 1d 105m8r 1 20 + ? 6 10 8 6 16 32 25 0.5 tc a 1e 155m8r 1.5 20 + ? 8 12 10 3.4 16 32 25 1.2 tc a 1e 475m8r 4.7 20 + ? 6 10 8 7 22 44 35 0.5 tc a 1v 105m8r 1 20 + ? 6 10 8 4.8 16 32 25 0.8 tc a 1e 335m8r 3.3 ? ? 20 + ? =under development part no. rated voltage 85 c (v) category voltage 125 c (v) surge voltage 85 c (v) cap. 120hz ( f) tolerance (%) leakage current 25 c 1wv.60s ( a) df 120hz (%) ? 55 c 125 c 25 c 85 c impedance 100khz ( ) 7/7 www.rohm.com c 2011 rohm co., ltd. all rights reserved. 2011.06 - rev.f data sheet tc series a case ? packaging specifications taping [a case] case code a a 0.1 + ? b 0.1 + ? t 1 0.05 + ? t 2 0.1 + ? 1.9 3.5 0.25 1.9 feeding direction 2.0 0.05 4.0 0.1 4.0 0.1 a b 8.0 0.2 3.5 0.05 1.75 0.1 chip 1.5 + 0.1 ? 0 t 2 t 1 ? packaging style 2,000pcs case code packaging taping a case packaging style plastic taping 180mm reel symbol r basic ordering unit s reel [a case] 13 0.2 60 + 1 0 0 ? 1.5 180 9.0 11.4 1.0 label sticking position eiaj et ? 7200b compatible pull direction + ? + 1.0 0 + ? r 1 120 a ww w .rohm.com ? 20 1 1 rohm co., ltd. all rights reserved. notice rohm customer support system http://ww w . r ohm.com/contact/ thank you for your accessing to rohm p r oduct informations. mo r e detail p r oduct informations and catalogs a r e available, please contact us. notes |
Price & Availability of TCA1A156M8R |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |